How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models comes with a keyless entry system built into. The key functions like a remote control and can be exchanged by an Kia dealer.
Key fobs may stop working due to a variety of reasons, including a dead battery, worn-out buttons signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key working again.
How do you replace the remote key or smartkey
The battery in your Kia's intelligent key will eventually require to be replaced, whether it's a remote key as well as a push-to start key or a normal metal key that doesn't have a transponder. This is particularly in the event that your car displays a message that the smart key or remote has low battery power.
It's a simple process. To replace the battery in the key fob take the mechanical key from the hole in the back of the key fob. You then need to break the cover. A small screw will be inside the key fob, which holds the battery in the correct position. Utilizing a small screwdriver take the screw off and pull out the battery that was in place. Then insert the new one and close the hole in the key fob.
When the key fob is equipped with a fresh battery check it by pressing the locks and unlock buttons. If the doors lock and unlock exactly as you expect, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to run errands around Brandon.
Note: Some key fobs (transponder chip or smart keys) may require their programming completed. This requires a programing machine, which is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need write down the key code's number on the tag for the key code.
How to replace the battery
If the Kia key fob does not respond to pressing the lock or unlock button, it is most likely that the battery is depleted. kia smart key The Key Lab could cause other problems like the check engine light flashing on or delayed engine cranking. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires only a few tools.
Make sure to shut off your vehicle and close all doors prior to beginning. Find the small metal or plastic piece that is on the bottom of your key fob and gently jiggle it until the metal key pops out. Then, you can put the key into the handle on the door of your driver to open your car.
To replace the battery in the key fob, take off the cover that covers the rear. Utilize a plastic plier tool to open the latch that holds the black negative cable. Remove the old battery, and then align the replacement battery to ensure its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the metal contacts.
After installing the new battery, turn the key fob on and off in the ignition until the door locks cycle. You can then test your Kia's key fob to ensure it's functioning properly.
How do you replace a smart key
Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key is equipped with an embedded mechanical key blade unlike the standard key fob, which does not. Both kinds of key fobs come with an internal battery that will eventually have to be replaced. Luckily, this is an easy task that will take about two minutes.
Before you begin before you begin, make sure that you are on a flat surface with enough lighting and that the Kia is off. Remember that the fob contains tiny parts that could be thrown off should you not be careful.
The first step is to find the small release button on the lower backside of your fob. It could be an oval or circular slot. Once you press this, the mechanical key blade will appear and you will be able to open the key fob.
Once you have the key fob open, you can simply remove the old battery and replace it. The new battery is a one called CR-2032 and can be purchased from a local or online auto parts shop. Once you're done, your key fob will allow you to lock and unlock your vehicle, even if it isn't running.
How do you replace a mechanical key
The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car by pressing a button. As with all devices that is used, the Kia key fob can have issues at times. There are steps to take to fix these issues and keep our key fobs in good working order for the long run.
A dead or drained battery is among the most common issues. This can cause the device to stop working completely or stop working at times. If this is the case it is time to replace the battery a new one.
If this doesn't fix the problem then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.
Close and open the door using the mechanical key. (Every kia fob comes with a spare mechanical key that fits into the slot). Test the key fob and make sure it is working properly. Contact a dealer, or a locksmith to resolve the problem in the event that the key fob is not working. Make sure they cut you an emergency key that functions for all trunk and door cylinders, to avoid lockouts again.